A welded fixture reaches inspection, with mounting holes inside a narrow bracket. The drawing shows their locations, but a scanner cannot capture every bore wall. Surface scanning could miss a feature critical to assembly.
Creaform HandyPROBE measures selected points directly, including holes, edges, and optically inaccessible features. That difference often determines whether the inspection report supports a defensible decision.
Why Surface Scanning Cannot Measure Everything
Optical scanners need a clear view of the surfaces they capture. Deep holes, recessed shoulders, and walls behind brackets can block the projected light or camera view. The mesh may look complete while missing internal geometry.
A tactile probe follows a different principle. Its tip physically contacts accessible points, and the measurement system calculates their coordinates. It does not need to image the entire feature.
That matters for hole centers, planes, and geometric relationships. However, the probe tip still needs physical access. A completely sealed cavity remains inaccessible without an opening or alternative inspection method.
How HandyPROBE Measures Geometric Features
HandyPROBE is a portable optical coordinate measuring machine, or CMM. A C-Track optical tracker observes the wireless probe and establishes its position relative to the measurement reference. The operator touches selected locations rather than collecting millions of surface points.
Creaform lists 0.030 mm accuracy for HandyPROBE Next+ and 0.025 mm for Next+ Elite. These specifications describe defined tests, not guaranteed job accuracy.
Dynamic referencing helps the system account for supported movement within the setup. Stable parts, correct technique, and calibration still matter.
Measuring Hole Centers and Diameters
Touch several appropriately distributed points along an accessible bore, then fit a circle or cylinder in the inspection software. The number and location of points matter because sparse sampling can miss form errors.
For four mounting holes, compare center distances and positions against drawing datums. A measured diameter alone cannot establish whether the pattern will assemble correctly.
Checking Edges and Planes
Probing points along accessible edges can help establish locations and distances. Where geometry permits, points across a surface define a plane for checking flatness or relationships to another feature.
Be careful with rounded, burred, or damaged edges. An ambiguous contact location can undermine the result. Specify the intended feature definition before interpreting measurements.
Inspecting Recessed and Partially Hidden Features
Consider a machined housing with a counterbore behind a flange. A scanner may capture the opening but not enough of the recessed shoulder to evaluate its depth. A suitable probe stylus may reach the shoulder directly.
The word hidden needs qualification. HandyPROBE can measure obstructed features only when the tip can contact them and the tracker can maintain the required visibility of the probe. Tooling, part orientation, and stylus geometry can limit access.
Operators should confirm clearance before probing narrow spaces. Contact must be controlled to avoid bending slender features or damaging finished surfaces. Sometimes a smaller tip, different approach angle, or secondary instrument is the better choice.
Build an Inspection Workflow Around the Drawing
First, identify the critical dimensions and geometric tolerances. Note datum surfaces, hole patterns, inaccessible areas, and features that need complementary measurements.
Next, secure the component and establish the reference system. Place the C-Track with an appropriate view of the working region, and check the setup using the manufacturer’s guidance.
Then probe datum features before evaluating the dependent geometry. Collect sufficient points for each circle, plane, or cylinder, avoiding burrs and visibly damaged regions unless those defects are specifically under investigation.
Finally, compare results with CAD or drawing limits and document the alignment method, point strategy, and decision rule. Repeat critical measurements when uncertainty or unexpected results warrant confirmation.
Do not let automatic fitting replace engineering judgment. A best-fit alignment may disguise a hole-position problem that datum-based inspection would expose.
When to Combine HandyPROBE With 3D Scanning
Probing and scanning answer different questions. A scanner efficiently captures broad surfaces for deviation maps, while a probe targets critical features requiring direct point measurements.
For a large casting, technicians might scan the exterior and probe mounting bores or reference planes. Combining methods can make inspection more complete without pretending either instrument measures every feature perfectly.
The right choice depends on tolerance, accessibility, setup time, and the evidence needed for acceptance.
Everything About HandyPROBE Inspection
Can HandyPROBE inspect deep holes?
It can inspect accessible features with suitable probe reach and tracking visibility. Deep or narrow bores may require different stylus configurations or another instrument.
Does HandyPROBE replace a traditional CMM?
Not always. It offers portable probing for shop-floor applications, while laboratory CMMs may remain preferable for particular tolerances, geometries, or controlled measurement procedures.
Can it measure hole position against CAD?
Yes. With appropriate datums and sufficient contact points, inspection software can calculate feature location and compare results with specified tolerances.
Is optical tracking the same as laser scanning?
No. The tracker locates the contact probe; the stylus physically touches the part. Laser scanners instead collect surface geometry using reflected light.
Put Difficult Features to the Test
Bring the component that gives your current inspection method trouble, together with its drawing and acceptance criteria. Ask to see how the operator reaches the feature, establishes datums, and documents results.
Dynamic 3D, an authorized Creaform reseller in Allen, Texas, can demonstrate HandyPROBE on representative parts and help determine where contact probing belongs in your quality workflow.
